TRACE THE
FAILURE
NUCLEAR SYSTEMS & HUMAN FACTORS

Three Mile Island’s light went dark.
The valve stayed open.

The control room showed an electrical condition. Operators needed to know the valve’s physical position and whether the core still had enough coolant.

Follow the evidence
Illustrative nuclear power station and cooling towers beside a river before dawn
AI-generated power-station illustration from the episode. Not an archival photograph of the accident.
THE COMPANION FILMThe Broken Switch That Melted a Nuclear Reactor Watch episode 6:39

What caused the Three Mile Island accident?

A relief valve stuck open at Three Mile Island Unit 2, allowing reactor coolant to escape. The control-room indicator did not measure the valve’s actual position: it reflected electrical power to its operating solenoid. When the light went out, operators believed the valve had closed, although coolant was still being lost. Technical Assessment, PDF pp. 14 and 101.

The valve problem became a much larger accident because the plant’s indications, procedures and training did not give operators a reliable understanding of the cooling condition. A high level in the pressurizer was mistaken for reassurance that the core had enough water, and emergency injection was reduced. Technical Assessment, PDF pp. 15–18.

Watch the explanation

Trace the coolant loss and see why pressurizer level could not reliably show whether the core was covered.

A shutdown reactor still needed cooling

At about 4 a.m. on March 28, 1979, the steam generators lost feedwater. With less heat being removed, pressure in the reactor coolant system rose and the pilot-operated relief valve opened. The reactor shut down automatically, reducing heat generation to the decay-heat level. That remaining heat still needed cooling. Technical Assessment, printed p. 8.

As pressure fell, the relief valve should have closed. Instead it remained open. A separate upstream block valve could isolate that path, but it was not closed until about 142 minutes into the event. The continued opening allowed a small-break loss-of-coolant accident to develop. Technical Assessment, printed pp. 8–9.

Temperature downstream of the valve and other plant indications could have helped reveal the leak. Operators found those signals ambiguous, for reasons examined in the report. They had clues beyond the misleading light but could not reliably interpret them together.

Why a high pressurizer level could mislead

The pressurizer helps control pressure in the reactor coolant system. Its water level is useful information, but it is not a direct measurement of how much water covers the reactor core.

During the accident, steam accumulated elsewhere in the system. That changed the relationship between pressurizer level and the total coolant inventory. Operators reduced high-pressure injection in response to the high pressurizer level, while coolant continued escaping faster than it was being replaced. Technical Assessment, printed p. 9.

Training had emphasized avoiding a system completely filled with liquid. The commission’s technical assessment found that operators were not adequately prepared to recognize this loss-of-coolant condition or interpret the relationship between level and pressure. It also found that the training simulator could not reproduce the accident sequence before it occurred. Technical Assessment, printed pp. 11–12, 34–35.

The lesson for control-room design

As circulation was lost and insufficient coolant remained over the core, fuel damage developed. Restoring stable cooling required more than closing the leaking path. The event exposed weaknesses in training, procedures, information presentation and the way operating experience was used. Technical Assessment, event sequence and training findings.

The commission called for fundamental changes in nuclear safety practice, including better training and attention to the human-machine interface. Its recommendations addressed the conditions in which operators made decisions as well as their individual actions. Commission report.

An indication needs to confirm the physical condition that matters. At Three Mile Island, the light showed the electrical command to the valve, leaving operators mistaken about its position. That misunderstanding helped turn a manageable equipment fault into a severe reactor accident.

The source record

President’s Commission: Technical Assessment of the TMI Accident

1979 · Printed pp. 8–12 / PDF pp. 14–18: event sequence. Printed pp. 34–37 / PDF pp. 40–43: training and control room. Chronology: PDF pp. 101–103.

Report of the President’s Commission on the Accident at Three Mile Island

1979 · Commission findings and recommendations; article distinguishes recommendations from later implementation.

Research checked September 21, 2026. Illustrative episode images are not primary evidence.